Reasons for the vibration of the spindle of woodworking CNC woodworking router machine Upload to:09-26 2021

  The electromechanical spindle of cnc woodworking router machineis the most important component of the CNC woodworking CNC cnc router machine. If the customer encounters a spindle jitter failure when using the CNC woodworking cnc router machine, the maintenance personnel are not present and do not know how to repair it. This editor teaches you a few ways to identify the reasons for the vibration of the electromechanical spindle of the CNC woodworking cnc router machine.

  General cnc woodworking router machinespindle jitter is caused by the low spindle speed of woodworking cnc router machine, excessive chip speed or high product density. The vibration of the spindle of the cnc woodworking router machinemay be caused by the following reasons:

  1. The level of the cnc woodworking router machineis not adjusted properly;

  2, the clearance of the spindle bearing of the cnc woodworking router machineis too large;

  3. The speed of the cnc woodworking router machineis too high;

  Whether the spindle speed and processing cutting speed are within a reasonable range, like materials with relatively high engraving density, if the rotation speed is low and the processing speed is relatively fast, it will also cause the spindle to shake. At this time, the feed speed can be appropriately reduced.

  4. The workpiece is asymmetrical, and the center of gravity does not coincide with the middle of the CNC woodworking cnc router machine;

  5. Whether the parameters of the cnc woodworking router machinecontrol system (mainly pulse equivalent, linear acceleration, and curve acceleration) are correct. If the parameters are not correct, the machine will run unsteadily. In severe cases, the spindle will shake severely.

  6. Whether the slider of the cnc woodworking router machinecan be loosened;

  7. It is to see whether the spindle bearing is worn or not;

  8. It depends on whether your graph is a small line segment.

  9. It is caused by the loosening of the spindle motor and the motor base, and we need to tighten it with an Allen wrench;

  10. The gap between the guide rails of the cnc woodworking router machineis too large or the strength of the tool bar is not enough (but you are talking about the vibration of the spindle of the CNC woodworking cnc router machine, which is unlikely).

  The solutions to solve the spindle jitter of the cnc woodworking router machineare as follows:

  1. When you find that there is a jitter situation, adjust the feed rate according to the possible situation above, and it is enough to adjust the feed rate. If it is a little slower, the quality can be guaranteed. The machine with the same material performance is relatively fast and accurate.

  2. When the cnc woodworking router machineencounters such a failure, do not rush, stop the machine and analyze one by one. If you feel any difficulties, you can contact us in time and let us solve it in time.

  If a cnc woodworking router machinewants to engrave things perfectly, it is inseparable from the precision of the CNC woodworking cnc router machine, and the precision of the cnc woodworking router machineis reflected in the verticality, flatness, positioning accuracy, and repeated positioning of the equipment. Parameters such as accuracy.

  It is also important to see that the surface is uneven when milling a plane with a large pitch with a flat-bottom knife. If the surface is not flat, the carved workpiece will also be uneven.

  The above are the reasons and solutions for the jitter of the cnc router machine spindle. If you have any questions, you can directly consult our online customer service to solve it for you.

Cncmachine.wiki supply Cnc Machine guide for EDM,Cnc Punching Machine,Cnc Milling Machine,Cnc Lathe Machine,Cnc Carving Machine,5 Axis Cnc Machine,Cnc Engraving Machine,Laser Cnc Machine,Metal Cnc Machine,CNC Bending Machine,CNC Grinding Machine,Home Cnc Machine,Wood Cnc Machine,3D Cnc Machine,Cnc Router Machine,Desktop Cnc Machine,Boring Machine,Swiss Machine,Turn-Mill Machine,CNC Spinning Machine,CNC Polishing Machine,Pipe Cnc Cutter,Hydraulic Press and Edge banding machine etc.

Please keep the source and address of this article for reprinting:Reasons for the vibration of the spindle of woodworking CNC woodworking router machine Upload to:09-26 2021

Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.:Cnc Machine Wiki,Thanks